The Kenmore refrigerator 795 is well-known for producing high-quality ice and being energy efficient. However, the ice maker has a few mechanical flaws that you may repair over time. So, do you suspect a Kenmore Refrigerator 795 ice maker problem but can’t nail it down?The good news is that most of these ice maker issues are fixable. Some call for you to clear a drain line, replace a filter, defrost something, or change the temperature setting. I’ll go through each of these nine difficulties in depth so you can find the specific problem with your Kenmore refrigerator 795 ice machine and fix it.
Quick Kenmore Refrigerator Model 795 Troubleshooting
As the table below demonstrates, all these nine issues are due to different causes, and once you identify the reasons, you can fix them individually.
| Kenmore 795 Ice Maker Problem | Probable Cause | Quick Fix | |
| 1. | Ice Making Leaking | Malfunctioning fill valve Frosted fill tubeLow water pressure Drain clogging |
Replace the fill tube Unfreeze the fill tube by running hot water through it Adjust the water pressure or fit a low-pressure valve Clean the condensation drains Remove the ice mass Replace the expired filter |
| 2. | Slow Ice Maker | High temperature Faulty water filter Blocked water line Overstocking or understocking |
Reduce the temperature to 12 0F Replace the filter Remove the source of blocking Don’t overstock or understock your unit |
| 3 | Ice Maker is Not Making Ice | Frozen line/ evaporator coil Clogged water filter Faulty water inlet valve Incorrect temperature Defective thermostat Failing ice maker |
Unclog the waterline and condenser coil Replace the water filter Replace faulty inlet valve Readjust the temperature to 12 0F Replace the thermostat Kenmore Elite 795 ice maker replacement |
| 4. | Kenmore Ice Maker Freezing Up | Inadequate water supply The fridge door doesn’t shut well |
Improve water supply Fix the door to ensure it shuts completely |
| 5. | Kenmore Ice Maker Not Dispensing Ice | Ice clog Faulty actuator Faulty motor Faulty control board Dirty condenser Defective door switch Faulty heating element |
Remove the ice clog Replace the actuator Replace the motor Replace the control board Clean the condenser Replace the bad door switch Replace the heating element |
| 6. | Ice Maker Dispensing Little Ice | Incorrect temperature Faulty water filter Frozen or clogged drain Out-of-level fridge |
Adjust the unit’s temperature Replace the faulty filter Unclog the water line Level the Kenmore unit |
| 7. | Ice Maker Dispensing Too Much Ice | Wrong ice bin position Problem feeler arm Low pressure Defective water inlet valve |
Reposition the ice bin properly Replace the broken feeler arm Adjust the water pressure Replace defective water valve |
| 8. | Kenmore Ice Maker Not Filling With Water | Clogged drain Faulty water inlet valve |
Unclog the drain Test the continuity of the valve and replace it if faulty |
| 9. | Ice Maker Suddenly Stops | Ice obstruction on the ejector’s arm | Remove ice obstruction on the ejector’s arm |
Diagnosing Your Kenmore Refrigerator 795 Ice Maker Problem and Fixing It
1. Kenmore Elite 795 Ice Maker Is Leaking
A leaking ice maker is inconvenient, and the Kenmore refrigerator 795’s ice maker may leak into the freezer, ice bucket, ice bin, or floor.Overall, the following are the possible causes of the leaking:
a) A faulty fill tube The Kenmore Icemaker gets water from the fill tube. If the fill tube fails, water cannot enter the ice maker and instead leaks into the freezer.Fix If the ice bucket’s fill tube is broken, remove it and replace it.
b) Frosted fill tube
Sometimes the fill tube is OK but can’t do its function because it’s frozen. As a result, rather of filling the ice maker, the water will flow onto the floor.Fix Unfreeze the fill tube by running hot water through it. Alternatively, switch off the unit and leave the door open for 30 minutes to let the ice to melt on its own.
c) Drain Clogging
Condenser drains acquire dirt over time, which can clog them. If this happens, water may begin to flow into the freezer.Fix Clean the condensation drains, which are located at the bottom of the freezer.
d) Expired Filter
If the filter fails, it might be a cause of the leak. Fix Check the filter’s expiry date and replace it if necessary.
e) Ice Jam
As the temperature in your freezer drops, the ice in the ice bucket may combine to create a big mass, causing leaks into the ice bin. Fix Unplug the device and remove the ice mass. You may also leave the freezer open for 30 minutes at room temperature.
f) Low Water Pressure
Your ice machine requires at least 20 psi to function properly. If the pressure decreases below a certain level, the ice machine will fill with water and leak.Fix Adjust your home’s water pressure or replace the present valve with a low-pressure alternative.
2. Slow Kenmore Refrigerator 795 Ice Maker
The ice maker may occasionally dispense ice slowly, which can be aggravating. If that’s the case, look into any of the following:
a) High Temperature
The temperature of your Kenmore ice maker should be around 120°F. If this is not the case, the ice creation process will be slowed.Fix Set the freezer temperature to 12 0F.
b) Faulty Water Line
Examine the waterline of your unit for ice or debris blockage or kinks.Fix Remove any obstructions, ice masses, or kinks from your water line.
c) Blocked Water Filter
A blocked water filter just slows ice production by restricting water flow to the ice maker. Fix If the water filter is dirty and blocked, it should be replaced.
d) Overstocking or Understocking
When you overstock or understock the refrigerator, you push it to work harder to chill stuff, which slows down the ice-making process.Fix Don’t overstock or understock your Kenmore refrigerator.
3. Kenmore Refrigerator 795 Ice Maker Isn’t Making Ice
If your ice maker isn’t producing any ice, it might be one of the following:
a) Frozen Line Or Evaporator Coil If there is ice mass on the waterline or evaporator coil, the ice maker will not produce ice.Fix Unfreeze and clean the waterline and evaporator coil.
b) A clogged water filter
A blocked water filter not only fails to collect contaminants, but it also interferes with the ice maker’s water supply and ice production.Fix Replace the water filter to increase water supply and ice production.
c) Faulty Water Inlet Valve
The water inlet valve may fail owing to an electrical or mechanical issue, interfering with ice formation.Fix Check for faults using a multimeter, but replace it if the water entry valve is defective. Kenmore Elite 795 Ice Maker Replacement
d) Incorrect Temperature Setting
If the ice maker’s temperature is too low or too high, it will not produce ice. Fix To encourage ice production, set the ice maker temperature to around 12 0F.
e) Defective Thermostat
The ice machine will not operate if the thermostat is broken. Fix Replace the broken thermostat.
f) Failing Ice Maker
If the ice maker is too old or sufficiently damaged, it will most certainly fail. Its sensors and inner arm, in particular, may fail, leading the entire apparatus to malfunction. Fix Replace your Kenmore ice maker.
4. Kenmore Refrigerator 795 Ice Maker Freezing
The ice machine may occasionally freeze. Some of the causes for this include:
a) Inadequate Water Supply If there is insufficient water supply to the ice tray, the sensor will fail to detect anything, allowing the water to overflow and freeze. Fix Increase the ice tray’s water supply.
b) Poor Door Closing
If the Kenmore freezer door does not close properly, warm air will enter the freezer, causing the ice to momentarily melt before refreezing. Fix Repair the freezer door so that it closes fully.
5. The Ice Maker Isn’t Making Ice
In rare circumstances, the ice maker may produce ice but fail to discharge it. If that’s the case, the cause might be:
a) Ice Clog
An ice blockage will prohibit your Kenmore ice maker from producing any ice.Fix Check for ice clumps around the bin and on the dispenser with your ice maker and melt them. You can use a hairdryer.
b) Faulty Actuator
The actuator is essential in transferring signals to your Kenmore ice maker. As a result, it shouldn’t be defective.Fix If the actuator is defective, replace it; however, first check its continuity with a multimeter.
b) Faulty Control Board
The dispenser’s control board should not be malfunctioning. You can detect whether its displays are dim.Fix Bring your Kenmore unit to a fridge specialist for assistance in replacing the control board.
c) A faulty door switch
The door switch that turns off the dispenser should operate properly. If it’s broken, you won’t be able to turn the dispenser off or distribute any ice. Fix Using a multimeter, check for continuity and replace the door switch if it’s broken.
d) Faulty Motor
If the motor that drives the auger fails, the ice maker will not produce any ice. Fix Check the continuity of the motor using a multimeter. If there is no continuity, you should replace the motor.
e) Dirty Condenser
The condenser quickly clogged with debris, preventing it from detecting temperature changes and impairing ice dispensing.Fix To clean the unclean condenser, use a condenser cleaning brush.
f) Faulty Heating Element
A heating source under your freezing tray heats the tray, requiring ice dispensing. If it’s broken, the ice machine won’t work.Fix Replace the defective element. More Diagnosis of the Kenmore Refrigerator 795 Ice Maker.
6. Ice Maker Produces Small Amounts of Ice
If your ice maker only produces tiny or hollow ice, the problem might be any of the following:
a) Incorrect Temperature If the temperature is too high or too low, the ice maker will produce hollow/small ice. Fix Using a fridge thermometer, check the temperature of the device and make any necessary adjustments. Kenmore elite 795 ice machine is leaking
b) Faulty Water Filter
If the water filter becomes clogged or worn out, it will impede water passage into the ice maker, lowering ice dispensing.Fix Replace the water filter
c) Frozen or clogged drain
If the waterline has kinks or obstructions, it will disrupt the water flow and ice dispensing. Fix Clear any clogs and kinks in the drains.
d) Low-level Refrigerator
The ice production and dispensing will be affected if the refrigerator is not at the proper level. Fix Reposition the Kenmore refrigerator to ensure it is level.
7. Ice Maker Produces Too Much Ice
On the other hand, your ice maker may produce a big volume of ice for the following reasons:
a) Incorrect Ice Bin Position
If the ice bin is out of place, your ice maker will appear to be overflowing.Fix Check that the ice bin is in the proper position.
b) Broken Feeler Arm
The feeler arm functions as an ice maker sensor. So, if it’s malfunctioning, the ice maker won’t detect a full bucket of ice, causing the ice to overflow.Fix Find an expert to assist you in replacing the damaged feeler arm.
c) Low Pressure
If the water pressure is low, the input valve will not close, allowing the ice to flow constantly.Fix Using a water pressure gauge, set the water pressure to around 20 psi. Kenmore Elite 795 Ice Maker Replacement
d) A faulty water inlet valve
A faulty water entry valve will not regulate water flow, and as long as water overflows, so will the ice.Fix Using a multimeter, test the water inlet valve and replace it if it is malfunctioning.
8. Kenmore Refrigerator 795 Ice Maker Not Filling With Water
Here are several reasons why your ice maker isn’t filling up with water:
a) Blocked Drain/Filter
If the drain or filter is clogged, the Kenmore ice maker will not fill up.Fix If the filter is blocked with dirt, replace it and clear the drain.
c) Faulty Water Inlet Valve
The water intake valve’s duty is to manage the water in the ice maker. So, if it’s broken, water won’t flow into the ice maker.Fix Using a multimeter, check the water intake valve for continuity (available on Amazon). If there is no continuity, replace the valve.
d) Out-of-Position Control Arm
The control arm of the Kenmore Ice maker is normally situated near the ice bucket. If the ice maker is out of place, it will not create ice. Fix Reposition the control arm and make sure it’s in the down position.
e) The unit must be reset.
If your icemaker needs to be reset after a significant repair, it may fail to fill. Fix Reset your ice maker by pushing the reset button, restarting the refrigerator, or repositioning the feeler arm.
f) The ice maker has been turned off.
You can’t expect the ice maker to fill up with water if it’s turned off. Fix If this is not the case, plug in the ice maker and turn it on.
9. Kenmore Elite Refrigerator 795 Ice Maker Not Working or Stops Suddenly
If your Kenmore ice maker suddenly stops while it is operating normally, ice is most likely impeding the ejector’s arm.Fix Remove the ice impediment that is stopping the ice maker from operating properly. Final Thoughts on Your Kenmore Refrigerator 795 Ice Maker Issue!The likelihood is that your Kenmore refrigerator 795 ice maker is not operating due to one of the concerns listed above. So, utilize the troubleshooting advice above to figure out what’s wrong with your Kenmore ice maker and then fix it.’
